Supply control
You start low and only increase as needed so the material has time to absorb the water.
Universal Dripper · Adjustable Flow
Dripper
A small, practical accessory that turns an ordinary bottle into a controlled water supply. You adjust the flow and direct the water where it's needed — to the top of a moss pole or into the pot's substrate.
AdjustableControl of water supply
UniversalFor common water bottles
2 usesMoss poles and pots
Tool-FreeInstallation without tools
Bottle above, test the flow
The water is released gradually
The Dripper connects to the bottle and allows you to reduce or increase the flow. Thus, the moss or substrate has time to absorb the water gradually, instead of receiving the full amount at once.
- It screws into a common bottle and is reused.
- Adjust the setting to the moss, substrate and size of the setup.
- The long spike keeps the delivery point stable.
- It is used on moss poles or directly in pots.
Correct setting requires a first test. The duration of a bottle is not constant: it changes with the position of the regulator, the bottle, the humidity of the material and the conditions of the room.
Two uses, one tool
The same Dripper can gradually feed a moss pole or direct water into the substrate of a pot.
Reusable bottle
No special container is needed. It connects to a common bottle, which you refill for the next application.
On the moss pole or in the pot
The position is different, but the principle remains the same: low initial flow, observing the material and making small corrections until you find the right rhythm.
At the top of the material
Attach the spike to the top and direct the flow to the moss. Set it slowly enough so that the material absorbs the water without rushing towards the pot.
On the substrate, not on the shoot
Place the spike firmly into the substrate, just outside the base of the plant. Watch if the water is absorbed properly and whether it reaches the drainage holes too quickly.
Start low Observe Increase slightly
The scale is a setting guide, not a time measurement or specific flow in ml.
Universal use with a bottle and the ability to adjust the supply depending on the setup.
The special Rapid Dripper fits on top, distributes water quickly and is available in the same size S–XL as the pole.
See Rapid Dripper →Fill, connect, turn, set
Do the first test over a sink or container. This way you can see the flow before placing the full bottle on the moss pole or in the pot.
Fill a clean bottle
Use water at room temperature and, for the first test, prefer a smaller bottle so you can handle it easily.
Connect Dripper
Screw it firmly onto the bottle neck. If the thread does not fit smoothly, try another common bottle instead of pressing it.
Invert and position
Hold the assembly upside down and place the spike in the selected spot, without injuring the stem or thick roots.
Open it slightly and observe
Start with a low supply. Check again after a while and increase only if the water is absorbed without overflow or rapid draining.
Don't judge the duration just by the size of the bottle
The same amount can be emptied in a very different time depending on the setting and setup. Monitor the first full-bottle test and do not leave the product unattended before making sure the flow is suitable.
For common bottles
The design is compatible with common water bottle necks. In a bottle with an unusual thread, check the fit before filling, or use a standard bottle.
Mechanical flow adjustment
The flow is changed by the Dripper regulator. It does not correspond to a predetermined time or specific ml per minute, so find the final position through small adjustments.
Clean flow, no complicated maintenance
A short check at intervals is enough to keep the Dripper ready for the next use.
Run water through the Dripper and rinse the connection points before storing.
Make sure the regulator moves smoothly and that the outlet is free of dirt, moss or scale.
Do not open the outlet with a needle or wire, as this may alter the setting or cause a leak.
In the package
1 Adjustable Bottle Dripper
Adjustable Dripper with bottle connection and long support pin.
Not included
Bottle and plant setup
Bottle, moss pole, sphagnum or other filling material, pot, substrate and plant.
Frequently asked questions
Does it provide automatic watering?
It releases water from the bottle while the flow remains open, without having to water at that time. However, it does not guarantee a specific duration or the same supply in each setup, so testing and monitoring is required.
How do I find the right flow?
Start with a low flow and observe if the moss or substrate absorbs the water without overflowing. Increase a little each time until you find a pace suitable for your setup.
Does it really fit every bottle?
The design is universal and intended for common bottle necks. If a bottle has an unusual thread or doesn't screw on smoothly, use a regular water bottle and don't force the connection.
Can it be used in both a moss pole and a pot?
Yes. In the moss pole it is placed on top of the material, while in the pot the spike goes into the substrate, a little outside the base of the plant.
How long does a full bottle last?
There is no fixed time. Duration varies with regulator position, bottle type, initial humidity, moss or substrate and room conditions.
How is it cleaned?
Rinse it with clean, lukewarm water and let water run through the outlet. Gently remove soil or moss from the outside, without a needle, wire or other sharp tool.
© Original product description by Greenleaf Garden Center. All rights reserved. | The text and diagram are original material. Copying is prohibited.